Abilis CPX 2000, release 8.11

New logger, specific handling for B365 and miniPC motherboards and SlotId handling for 4xEth cards and miniPC with 4xEth.

REALTEKG - Added support of 2.5Gbps speed for RTL8125 chip.

ETHUSBG - Added support of AX88179A chip, mainly it has different RX USB buffer structures.

Added DFT-CALL-LOG parameter: used to enable/disable user CALL-LOG when a new user is created.

The parameter is immediately active run-time. It does not need to be refreshed (INIT).

It is displayed in the 'Router' section:

[16:03:28] ABILIS_CPX:d p res:ctisys

RES:CtiSys --------------------------------------------------------------------
Run    DESCR:CTI_System_general_properties
       - Router ---------------------------------------------------------------
       ROUTING:PREFIX      max-c-tofrom-cisda:50    au-law:A-LAW    NPOO-CT:NO
       OUTDIAL-TONE:NO     OUTDIAL-DIGIT:0
       NAT-PREFIX:0        INT-PREFIX:00      COUNTRY-CODE:39
       OPC-QUEUES-PREFIX:                     DFT-CALL-LOG:YES
       ...

D LDM[E], D LDD[E]and START LDM[E] commands: added RX/TX/RXTX options to allow call direction selection (for E:CTIR only).

[16:03:44] ABILIS_CPX:d ldm ?

D LDM  [dd/mm/yyyy] [hh:mm:ss] [filter:val] [opt]   Display Debug Log in Memory 
...
Allowed options:

<call-dir>      Call direction:                              <Only for E:CTIR>
                - RX : Incoming (default)
                - TX : Outgoing
                - RXTX or TXRX : Incoming and Outgoing

NW or NOWRAP    Don't wrap line

[16:08:05] ABILIS_CPX:

Fixed de-referencing of NULL pointer causing an exception.

The problem could occurs in a very quick sequence of opening and closing of the session.

It has been highlighted for example with the SMTP driver, when there is a peak of mails to be sent.

None

None

Fixed JS exception generated in 'top 10' page when TRFA IP service is not active and the 'Download spreadsheet' button is clicked.

Figure: JS exception sample

Added user's SIP-PROVIDE-HI parameter (NO/YES) to control HistoryInfo presence in an outgoing INVITE.

Fixed CG/CD filters of D D[E] SIP and D SE SIP commands, which sometimes worked sometimes not, due to an inaccurate exchange of information between the driver and the command parser.

Fixed parsing and help of D[E] SIP and D SE SIP commands: CD/CG/USER filters in the format '*nnnn' and '*nnnn*' were accepted, but they should not because not supported.

Fixed parsing of D LDM[E] command: cd/cg/scd/scg filters in the format '*nnnn*' were accepted, but they should not because not supported.

None

None

Fixed missing CR/LF in the output of 'D SIP CALLS'.

Before the fix:

[08:19:48] ABILIS_CPX:d sip calls

110523 081933 start:2023-05-11 08:19:06.317 dur:2/25 user:admin Out CONN-TO cg:9002 cd:111 ip:192.168.0.2 rtp-I/O[1/1253 0/0 0/0 0/- 0/- 0/-] ses:2 id:2110523 081933 start:2023-05-11 08:19:06.317 dur:2/25 user:emanuela In CONN-FROM cg:9002 cd:111 ip:192.168.0.2 rtp-I/O[0/0 0/0 0/0 0/- 0/- 0/-] ses:2
 id:2110523 081940 start:2023-05-11 08:18:43.629 dur:2/56 user:admin Out CONN-TO cg:9002 cd:111 ip:192.168.0.2 rtp-I/O[0/2776 0/0 0/0 0/- 0/- 0/-] ses:1 id:1110523 081940 start:2023-05-11 08:18:43.628
 dur:2/56 user:emanuela In CONN-FROM cg:9002 cd:111 ip:192.168.0.2 rtp-I/O[0/0 0/0 0/0 0/- 0/- 0/-]
ses:1 id:1
[08:19:52] ABILIS_CPX:

After the fix:

[08:26:20] ABILIS_CPX:d sip calls

110523 082607 start:2023-05-11 08:25:50.713 dur:2/15 user:admin Out CONN-TO cg:9002 cd:111 ip:192.168.0.2 rtp-I/O[1/749 0/0 0/0 0/- 0/- 0/-] ses:2 id:2
110523 082607 start:2023-05-11 08:25:50.713 dur:2/15 user:emanuela In CONN-FROM cg:9002 cd:111 ip:192.168.0.2 rtp-I/O[0/0 0/0 0/0 0/- 0/- 0/-] ses:2 id:2
110523 082609 start:2023-05-11 08:25:43.787 dur:2/24 user:admin Out CONN-TO cg:9002 cd:111 ip:192.168.0.2 rtp-I/O[1/1211 0/0 0/0 0/- 0/- 0/-] ses:1 id:1
110523 082609 start:2023-05-11 08:25:43.787 dur:2/24 user:emanuela In CONN-FROM cg:9002 cd:111 ip:192.168.0.2 rtp-I/O[0/0 0/0 0/0 0/- 0/- 0/-] ses:1 id:1

[08:26:24] ABILIS_CPX:

The bug has been introduced starting from release 8.11.9 (build 4715.47).

None

Added support for M/B with CPU Intel J4125 with BIOS ReleaseDate 09/14/2022 detected on the miniPC with 4xEth Intel i211 MB.

Added support for AUTO WARM START in Ethernet driver in case of troubles with PCI identification of on-board RealTekG of Gigabyte P31-DS3L motherboard.

Changed 'UDT' parameter range from [NO, 1..9999 s] to [NO, 1..65535 s].

Changed 'T301' parameter range from [Dft, 5..180 s] to [Dft, 1..180 s].

Added to almost all drivers logs display the 'NOWRAP' option, it can be used to not wrap lines during display.

Example

[18:40:19] ABILIS_CPX:d sip log
. . .
Date   Time   Event Event detail
------ ------ ----- ------------------------------------------------------
090523 170315 Err   [0000]  in OUT channel with 192.168.13.7:7062
090523 170315 Err   [0000] 301 timer timeout
090523 170315 Err   [0000]  in OUT channel with 192.168.13.7:7062
090523 170315 Err   [0000] Sent closure cause:No answer from user (user
                    alerted)
090523 170317 Err   [0000]  in IN channel with 192.168.13.7:5060
090523 170317 Err   [0000] Sent closure cause:Service or option not available,
                    unspecified

[18:40:29] ABILIS_CPX:d sip log nowrap
. . .
Date   Time   Event Event detail
------ ------ ----- ------------------------------------------------------
Date   Time   Event Event detail
------ ------ ----- ------------------------------------------------------
090523 170315 Err   [0000]  in OUT channel with 192.168.13.7:7062
090523 170315 Err   [0000] 301 timer timeout
090523 170315 Err   [0000]  in OUT channel with 192.168.13.7:7062
090523 170315 Err   [0000] Sent closure cause:No answer from user (user alerted)
090523 170317 Err   [0000]  in IN channel with 192.168.13.7:5060
090523 170317 Err   [0000] Sent closure cause:Service or option not available, unspecified          

[18:40:39] ABILIS_CPX:

Fixed outgoing call indication in OPC when such a call is immediately closed by REJECT_INDICATION.

Fixed call duration diagnostic after 248 days of uptime when the system timer overflows.

Changed the rejection code from 403 to 503 when the incoming call is rejected on SIP-SES-IN exhaustion.

Changed the Q.850 rejection code from 41 to 34 when the incoming call is rejected on SIP-SES-IN exhaustion.

Added support of answered and immediately held call with multiple coders, unheld before MCS timeout (100ms) expires.

Removed CR and LF characters from records sent to SYSLOG.

They were shown at the end of SIP CALLS messages as '#015' (e.g. ".../- 0/-] ses:1519 id:1519#015") creating the impression that there was an error in the message content.

Fixed SYS UPDATE AUTO command. The Abilis fw update failed in case of redirection from HTTP to HTTPS.

Fixed overflow that caused caused the system to hang and reboot (WDLIVE1) when the number of user's local mail files was greater than 1000.

Fixed wrong checks of user mailbox limits, that allowed to save more files than the configured maximum (MAIL-MB-MAXMAILS).

None

Extended CDR logging to provide possible error code even in case of successful double-operation.

Fixed the wrong adding of Redirecting IE when the RGO macro evaluation is empty.

Fixed the fully static user (both HOST and REMPORT) recognition including also local port.

Fixed the fully static user (both HOST and REMPORT) recognition including also local address.

Added protection to DNS translation to avoid multiple translation on the same FQDN at the same moment.

Fixed the user distinguishing if their only difference is their remote IP.

Fixed bug introduced starting from rel. 8.11.7 (build 4715.32): splitted retransmission timer could cause a situation where TCP state could be blocked to FIN-WAIT-1 forever.

Fixed 'S SIP LOG EVENT:val' command: the 'DFT' value was present in the help but it was not settable:

[17:27:27] ABILIS_CPX:s sip log event:dft

BAD VALUE 'event:dft'

[17:27:36] ABILIS_CPX:

Now it works and setting the filter to 'DFT' corresponds to setting it to 'ERR' events plus 'INFO' events.

[17:15:04] ABILIS_CPX:s sip log ?

S [CTI]SIP LOG EVENT:val                              Set SIP log events filter

EVENT:         Log events filter [ERR, REG, INFO] or [DFT, FULL], where:
               - ERR, REG, INFO filters can be joined using ',' (comma);
               - DFT: means ERR and INFO events;
               - FULL: means every type of event.

[17:15:11] ABILIS_CPX:

Added escaping of CD/CG/SD/SG/RCD/RCG fields of 'D CTIC' and 'D CTICE' command output.

Non-printable characters and space character are replaced by '.' (dot).

Added escaping of CD/CG fields of EIR events of 'D LDM[E]' command output.

Non-printable characters and space character are replaced respectively with the following escape sequences:

• Space is replaced with ' \s '

• Tab is replaced with ' \t '

• Double quote is replaced with ' \" '

• Backslash is replaced with ' \\ '

• Other non-printable characters are replaced with ' \xHH ', where 'HH' is the ASCII hexadecimal value of the character

  Example:

  [18:07:29] ABILIS_CPX:d ldm
                    
  020323 170425 CtiSip       924  924 E-Route Match  PR:44
  020323 170425 CtiVo        924  924 E-CallTx       BC:Speech TY:StoA CD:12344\s CG:43321\x056
                                                     SCG:Svaitian Ebsai
  020323 170425 CtiVo        924  924 E-CallForward  RULE:ALWAYS USER:Toitop
  ...

None

Added support for RealTek 8125 Ethernet chip present on 4 port PCIe card (2.5 Gbps isn't supported now).

Added driver for Intel i211 Ethernet chip present on miniPC with 4 Ethernet chips.

Added new parameter 'LCP-ECHO', that can be used to disable/enable ECHO packets exchange.

[19:14:20] ABILIS_CPX:d p res:ip-3

RES:Ip-3   - IP over PPP (PPP) ------------------------------------------------
Run    DESCR:Ip-703
       ...
       - Ppp ------------------------------------------------------------------
       PPPLOG:DSAT+E    NRTY3:3         RADIUS:NO                 LCP-ECHO:YES
       PPP-ENC:RAW-PPP
       - Tcp-MSS/Lcp/IpCp -----------------------------------------------------
       ...
       - Authentication -------------------------------------------------------
       ...
[19:14:22] ABILIS_CPX:d p res:ip-3 ? lcp-echo

Ip-703 (IP over PPP) resource parameters:

LCP-ECHO:  Activate/deactivate LCP-ECHO request [NO, YES]

[19:21:13] ABILIS_CPX:

The PPP protocol uses ECHO-REQUEST/ECHO-REPLY packets exchange to maintain connection integrity.

Until now this feature has always been active by default. But unfortunately there are cases where the remote peer seems to be unable to answer to ECHO-REQUESTs, therefore it can be useful to have the possibility to disable them, if needed.

Fixed cold restart handling of REALTEK-8169SC(RTL_GIGA_MAC_VER_05) on Jetway MBs (CN700-8237).

Improved local IP address diagnostics in extended registration listing.

Fixed an exception in processing of malformed REGISTER response.

None

Added support for M/B with CPU Intel J4125 with BIOS Info: ReleaseDate 12/21/2020, System info: Vendor ANTEK and System info: Product mini-antek detected on one of miniPC with 2 Eth devices.

Added support for M/B with CPU Intel J4125 with BIOS ReleaseDate 09/26/2021 detected on the miniPC with 4Eth Intel i211 MB.

Fixed the procedure that adds 'system' contacts.

When Abilis user's ADDRBOOK-NUMBER parameter is set to AUTO, it had to use the first 'valid' number between the ones assigned to CTIP, CLUS, SIP, IAX and VO interfaces, instead it stopped to the first assigned interface and if the number was not 'valid' it did not add any 'system' contact.

Modified the number used for 'system' contacts resulting from VO when they are 'local' national number.

Before VO numbers were notmalized to 'unknown' Type of Number, always adding International prefix and Country code, regardless of whether they were foreign country numbers or local national numbers.

Now if they are 'local' national numbers, the International prefix and Country code are omitted.

For instance, with INT-PREFIX equal to '00' and COUNTRY-CODE equal to '39, before it was

[10:11:25] ABILIS_CPX:d contact sys

UUID:     4392A9002E000040A5C2E4FFDAC49E60
CONTACTs: 1/10000

--------------------------------+---------+------------------------------------
NAME:                           |OUTDIAL: |NUM:
--------------------------------+---------+------------------------------------
Foreign User                               00450011
Local User                                 00390022
--------------------------------+---------+------------------------------------

[10:11:34] ABILIS_CPX:

Now it is

[10:11:25] ABILIS_CPX:d contact sys

UUID:     4392A9002E000040A5C2E4FFDAC49E60
CONTACTs: 1/10000

--------------------------------+---------+------------------------------------
NAME:                           |OUTDIAL: |NUM:
--------------------------------+---------+------------------------------------
Foreign User                               004500011
Local User                                 00022
--------------------------------+---------+------------------------------------

[10:11:34] ABILIS_CPX:

Modified CG_UPDATE support to be performed only already in Active state. Some devices wrongly handle an UPDATE in Calling state.

Fixed processing of keepalive response SDP in case of REMOTE-NAT:STRICT to keep the voice stream flowing.

Fixed bug that caused state not to be destroyed in case of opening packet parsing error.

Added new DH group definition for IKE LOG for ECP256 and ECP384 groups.

Added vendor ID check also in third MAIN-MODE packet exchange.

Fixed obsolete, no longer working links to Abilis support tools and to Abilis manual.

CTI routings administration: fixed buffer overflow that causes malformed routings list responses.

Fixed 'D USER[:val] CTINUM' command: in some cases it did not show all numbers assigned to the user.

None

None

Fixed SMS OUT rule evaluation: when a TXT list was set in the SENDER-ID parameter, the routing was never matched even though the input SenderId was present in the list.

Fixed 'D SMS OUT' command layout: double quotes were missing when a TXT list was set in SENDER-ID parameter.

Before it was

[10:43:02] ABILIS_CPX:d sms out

----+-------+-------------------------+-----+---------+-------+-------+--------
PR: |ACT:   |CD:                      |POO: |LIFETIME:|DELAY: |SPLIT: |UNICODE:
    |SOURCE:|SENDER-ID:               |SMTP-SERVER:
----+-------+-------------------------+-----+---------+-------+-------+--------
0    YES     *                         G14   1800      300     SYS     SYS
     SMTP    ListOfSendId
-------------------------------------------------------------------------------

i.e. the content of SENDER-ID field can't be distinguished from a regular text.

Now it is

[10:43:02] ABILIS_CPX:d sms out

----+-------+-------------------------+-----+---------+-------+-------+--------
PR: |ACT:   |CD:                      |POO: |LIFETIME:|DELAY: |SPLIT: |UNICODE:
    |SOURCE:|SENDER-ID:               |SMTP-SERVER:
----+-------+-------------------------+-----+---------+-------+-------+--------
0    YES     *                         G14   1800      300     SYS     SYS
     SMTP    'ListOfSendId'
-------------------------------------------------------------------------------

Removed FRMWRs indicating possible and legal situation, to avoid false alarms.

• FRMWR indicating attempt to send FACILITY_REQUEST to already closed connection side.

• FRMWR indicating possible crossing of events DISCONNECT_INDICATION and RETRIEVE_RESPONSE.

Fixed memory exception caused by mistaken Cancel of NCB_LISTENs that were no longer available.

Fixed a bug that could cause an infinite loop without task-switches and consequent system restart.

It was caused by a wrong condition on a timer, which couldn't be satisfied.

None

Added S S CTIP:val PIN:val ON|OFF commands, used to activate/deactivate PIN protection.

[10:43:02] ABILIS_CPX:S S CTIP:501 ?

S S CTIP:val PIN:val ON|OFF        Activate/deactivate SIM PIN protection for
                                   the specified CELL Cti port

CTIP:      CELL CTI port identifier [[1..600]                       <Mandatory>
PIN:       SIM card PIN value. From 4 to 8 digits [0..9]            <Mandatory>
ON|OFF     ON=activate; OFF=deactivate the given PIN                <Mandatory>

[10:43:11] ABILIS_CPX:

Improved the D CTIP command for running ports: now the 'card' parameter also shows the CELLKEY/CELLBOX device to which the port belongs.

[10:49:42] ABILIS_CPX:d ctip:501,503,504

CTIP:501 DESCR:
Act     card:CELL32-1<1>,CELLKEY-1<1>   USER:#
Run     OPSTATE:UP        LOG:NO                               TYPE:NET-PUBLIC
        signalling:CELL                 HOLD:NO
        ...

CTIP:503 DESCR:
Act     card:CELL32-1<3>,CELLBOX-2<1>>  USER:#
Run     OPSTATE:UP        LOG:NO                               TYPE:NET-PUBLIC
        signalling:CELL                 HOLD:NO
        ...

CTIP:504 DESCR:
Act     card:CELL32-1<4>,CELLBOX-2<2>   USER:#
Run     OPSTATE:UP        LOG:NO                               TYPE:NET-PUBLIC
        signalling:CELL                 HOLD:NO
        ...

[10:49:48] ABILIS_CPX:

Improved the D CTIP command for running ports, present on POTSBOX device: now the 'card' parameter also shows the POTSBOX device to which the port belongs.

[03:50:08] ABILIS_CPX:D CTIP:105,136

CTIP:105 DESCR:
Act     card:BSE-1<13>,POTSBOX-1<1>     USER:#
Run     OPSTATE:UP        LOG:NO                               TYPE:USER
        signalling:POTS                 HOLD:YES     CT:ICT    SS:YES
        DEVICE:PHONE                                           AC:NO
        ...

CTIP:136 DESCR:
Act     card:BSE-1<44>,POTSBOX-1<32>    USER:#
Run     OPSTATE:UP        LOG:NO                               TYPE:USER
        signalling:POTS                 HOLD:YES     CT:ICT    SS:YES
        DEVICE:PHONE                                           AC:NO
        ...

[03:50:18] ABILIS_CPX:

Fixed calculation of call times even after 248 days of uptime when the system timer overflows.

Added support of new FACILITY event carrying CG_UPDATE code in CT resulting into StoS connection.

Modified CG_UPDATE procedure in CT resulting into StoS only for manual CT, not CF.

Fixed removal of SIPCAUSE IE on ISDN line with type different from NET-PRIVATE.

Added support of new FACILITY event carrying CG_UPDATE code during CT resulting into StoS connection.

Added UserInfo IE in REJECT_INDICATION event.

Added protection against stack overflow in recursive directory listing.

It happened that too deep nesting of directories caused a stack overflow to the thread responsible for system disk mirroring.

The unexpected and exaggerated directory nesting originated from File System corruption.

Fixed range of "BURST-DLY" parameters.

There were discrepancies between the range declared in parameter's help and the real accepted range.

Now the correct range is [10..100 ms] for NPV, NPV Links and Abilis IP tunnel v.2.

None

Added support for USB keyboard for all MBs.

Added support for new pieces of J4125 MBs which has changed BIOS release date in SMBIOS which is used for multicore detection.

Fixed channel diagnostics showing corrupted/truncated/missing CallID and User name fields.

The problem occurred when the CallID was longer than 31 characters and it was caused by not inserting the string terminator in the CallID field of the diagnostic.

Added protection against delimiter character (',') present in CD/CD/RG/SD/SG to keep the CDR file format correct.

Fixed bug with source routing addition, when they contain equal subnets but different outgoing IPs.

Previous version didn't allow multiple entries with same subnet and different IPs, it considered new entry as already existing.

Displayed IP Monitor diagnostics 'AnalysisUpTime' value was wrong.

The information received from the driver is in ticks and must be treated accordingly. Instead it was considered in seconds and the wrong conversion to date and time was applied.

Fixed bug in IP Monitor diagnostics management.

Because of the different endian, diagnostic records must be re-sorted before matching the requested OID (Object Identifier).

The bug caused lack of IP addresses diagnostic records.

Fixed syntax errors/warnings in MIB file, that could prevent MIB loading by some management tools.

LTE HUAWEI - NETWORK name loading is automatically switched to LONG/NUMERIC format when SHORT format has invalid results.

Trouble detected with some mobile operators.

Added support of RCC in legal MixWaiting state, instead of improper FRMWR.

Removed FRMWRs indicating possible situations during crossing of calls.

Added ACPI reset, which is used for J4125 MBs for which the use of RTReboot has proved ineffective.

None

Added support for alarms configuration from Videorecorder cameras settings pages.

Starting from rel 8.11.0, the alarms could only be seen and configured from the command-line interface.

[15:55:28] CPX_220:d p res:rvs-1

RES:Rvs-1 ---------------------------------------------------------------------
Run    DESCR:
       ...
       -------+-------------------------- Cameras -----------------------------
       CAM:   | [DESCR:]
       ACT:   | RESOLUTION:  ROTATION:  JPEG-QUALITY:  EXPOSURE-TIME:
              | PREVIEW:     HDR:       FLASH:         METERING:
              | SHARPNESS:   CONTRAST:  BRIGHTNESS:    SATURATION:
              | LAMP-THRESHOLD:         LAMP-DURATION: LAMP-ON-EXPOSURE-TIME:
              | STORAGE:                REC-MAXAGE:    IDLE-REC-INTERVAL:
              | MIN-ALARM-DURATION:     MAX-ALARM-DURATION:
              | ALARM-HOLDOFF:          LIVE-REC-DURATION:
              | [RES:                   IO:            TRIGGER:  ALERTS:]
       -------+----------------------------------------------------------------
       Cam-1  | Rvs1_Cam1
       YES    | 0.3          0          MEDIUM         AUTO
              | MEDIUM       NO         OFF            AVERAGE
              | 0            0          0              0
              | 0                       30             AUTO
              | SYS (40 GiB)            SYS (14)       SYS (60)
              | SYS (180)               SYS (600)
              | SYS (600)               SYS (600)
              | Rvs-1                   D-IN-1         *         #
       ------------------------------------------------------------------------

[15:55:34] CPX_220:d p res:rvs-1 ? res io trigger alerts

Rvs resource parameters:

RES:       Resource for which the event is monitored.
           # or type-nnn, where type can be [Mfio, Gpio, Rio, Rvs]
IO:        Input/output digital line for which the event is monitored.
           # or D-IN-n or D-OUT-n, where 'n' can be:
           - for Gpio, [1..16];
           - for Mfio, [1..7];
           - for Rio, [1..16];
           - for Rvs, [1..4].
                                                              <Only for RES <> #>
TRIGGER:   Event to be monitored [NONE, ON, OFF, *]
ALERTS:    Released alerts when the event is detected.
           # or list of up to 20 ALERT indexes [1..255] separated by ',' (comma).

[15:56:47] CPX_220:

Now, a summary of the alarm is shown in Cameras index page:

Figure: Videorecorder cameras settings

and dedicated alarm section allows alarm configuration in Camera edit dialog:

Figure: Videorecorder Camera edit

Fixed page fault causing a system crash when adding a contact to the Abilis address book and the address book is empty.

The bug was present starting from rel 8.11.0.

Fixed processing of double '180 Ringing' - 1st without SDP and 2nd with SDP. The bug caused the call drop.

Fixed clearing of UserInfo in SIP channel, to avoid a heap corrupting during SUBSCRIBE message processing.

Removed FRMWR indicating CT in unsupported but legal states combination (BZ 2484) where proper rollback is applied.

Fixed wrong check that prevent setting of 'MAIL-TO' parameter returning a false error.

None

Modified 'abilis.cpx.sleep' function to be interruptable before its expiry.

Before this fix, it was necessary to wait for the complete sleep time expiration to restart the LUA script again.

Fixed stack overflow causing a system crash when Lua script is performing CP command with '|' filter.

Fixed processing of TelEvent dynamic payload change from an outgoing connection side during the active state.

Fixed management of multiple concurrent accesses to the Leases table by adding a task switching that allows all processes to be correctly scheduled.

The bug caused that 'D DHCP BIND' command to appears freezed and pending for a long time.

Fixed bug in management of COSBALANCE:YES.

The bug caused that when the outgoing FIFO was FULL and LOW priority data have to be sent, if no LOW priority packet was present, the FIFO could be stuck forever until COSBALANCE: is set back to NO.

Fixed bug in management of OUTSPx.

The bug caused that sometimes the throughput was not properly limited accordingly to the value of OUTSPx parameter.

Fixed syntax errors in MIB file, that prevent MIB loading by some management tools.

None

Added support for INTEL YL-3160L2-V2 motherboard.

Extended Maximum number of configurable Sip numbers from 3000 to 30000.

The maximum number of Sip numbers can be configured in System General:

[12:24:47] ABILIS_CPX:d g ? maxsipnumbers

General system parameters:

maxsipnumbers: Maximum number of Sip numbers [3000..30000].
           It must be multiple of 1000 and not less than 'maxusers'.
           The value in brackets is the one currently in use.

[12:24:56] ABILIS_CPX:

New values are applied at next system reboot. The value currently in use is displayed in brackets.

[12:24:50] ABILIS_CPX:d g

------------------------ System General Parameters -----------------------------
---------------------+-------- Setup and debug --------+------------------------
tact:     YES  (YES) | listitems:       4000    (4000) | sound:       ON    (ON)
TSAVE:    YES  (YES) | maxusers:        1000    (1000) | stackovh:     0     (0)
ldmsize: 1024 (1024) | maxsipnumbers:   5000    (3000) | hookact:    YES   (YES)
LDM-FILTER: ALL                                        | HOOKTHR:     10    (10)
LDM-SYSLOG: ALL                                        |
---------------------- Settings and identification -----------------------------
TIMEZONE:   CET - Central Europe (Rome, Paris, Berlin, Prague, Brussels)                       
. . .

[12:24:57] ABILIS_CPX:

More SIP numbers requires more CPX list items, therefore as the number of SIP numbers increases, new value for "listitems" is eventually automatically calculated and set, if its value does not satisfy the rule below:

• 'listitems' must be >= 'maxsipnumbers' + 1000

Of course 'listitems' can also be further increased manually, if necessary.

Extended maximum number of configurable Users from 1000 to 10000.

The maximum number of Users can be configured in System General:

[12:22:26] ABILIS_CPX:d g ? maxusers

General system parameters:

maxusers:  Maximum number of Users [1000..10000].
           It must be multiple of 1000.
           The value in brackets is the one currently in use.

[12:22:33] ABILIS_CPX:

New values are applied at next system reboot. The value currently in use is displayed in brackets.

[15:24:40] ABILIS_CPX:d g

------------------------ System General Parameters -----------------------------
---------------------+-------- Setup and debug --------+------------------------
tact:     YES        | listitems:       5000    (5000) | sound:      OFF
TSAVE:    YES        | maxusers:        2000    (1000) | stackovh:     0
ldmsize:   50        | maxsipnumbers:   4000    (3000) | hookact:    YES
LDM-FILTER: ALL                                        | HOOKTHR:     15
LDM-SYSLOG: ALL                                        |
---------------------- Settings and identification -----------------------------
TIMEZONE:   CET - Central Europe (Rome, Paris, Berlin, Prague, Brussels)                       
. . .
[12:24:47] ABILIS_CPX:

More users requires more SIP numbers and more CPX list items, therefore as the number of users increases, new values for "maxsipnumbers" and "listitems" are eventually automatically calculated and set, if their values do not satisfy the rules below:

• 'maxsipnumbers' must be >= 'maxusers'

• 'listitems' must be >= 'maxsipnumbers' + 1000

Of course 'listitems' and 'maxsipnumbers' can also be further increased manually, if necessary.

Moreover a large number of users requires a large number of files/directories to be created on system disk.

For more efficient disk management we suggest using a system disk with exFAT file system.

A warning will be shown when setting 'maxusers' value. E.g.:

[15:48:01] ABILIS_CPX:s g maxusers:2000

WARNING: YOU ARE ALLOWING TO CREATE A LARGE NUMBER OF USERS,
IT IS STRONGLY SUGGESTED TO USE exFAT FILE SYSTEM ON SYSTEM DISK
CURRENT FILE SYSTEM:
- C: is FAT32

COMMAND EXECUTED

[15:48:14] ABILIS_CPX:

Added lists for TCP/UDP ports Replacements (TUPR).

[12:26:34] ABILIS_CPX:d list:tuprlist ?

. . . 

List type:

TUPR:    TCP/UDP ports Replacement:
         - Destination port: mnemonic or decimal value [1..65535]
         - Alias port: mnemonic or decimal value [1..65535] or '*'
         See also HELP INTERNET PORTS.

[12:33:08] ABILIS_CPX:a list:tuprlist ?

. . . 

Possible Item values for TUPR list Type:

TUPR item:   Sequence of two values separated by ',' (comma) e.g. 'dpo,apo',
             where:
             - 'dpo' is the destination TCP or UDP port mnemonic or decimal
               value [1..65535]
             - 'apo' is the alias TCP or UDP port mnemonic or decimal
               value [1..65535] or '*'
             See also HELP INTERNET PORTS.

[12:33:12] ABILIS_CPX:d list:tuprlist

LIST:tuprlist             - TUPR              - Ref-Numb:0     Items-Numb:4
     --------------------------------------------------------------------------
     Destination Port         Alias Port (Translated)
     snmptrap(162)            *
     https(443)               http(80)
     1500                     1501
     6500                     ike500(500)

[12:33:18] ABILIS_CPX:

These lists can be used in DPO parameter of NAT Alias records. See NAT section for more details.

Added the use of the TUPR list for the 'DPO' parameter in NAT Alias.

[14:55:36] ABILIS_CPX:d nat pr: ? dpo

. . . 

NAT alias entry parameters:

DPO:       Allowed destination TCP/UDP port(s):       <Only for PROT:*|TCP|UDP>
           a single port mnemonic or decimal value [1..65535] or two port
           values separated by ':' (colon) or * (Any port) or the name of a
           TUP/RU/MR list between single quotes or the name of a TUPR list
           between double single quotes.
           (E.g. 22 or SSH or 1:1024 or * or 'List' or ''tupr-list'')
           TUPR lists can be used only when ADD:DST.
           When 'DPO' refer to a TUPR list, 'APO' is not allowed.

[15:07:19] ABILIS_CPX:

TUPR lists contain a list of "destination port, alias port" pairs to use.

When in the 'DPO' parameter we have a TUPR, the alias is taken directly from the list, ignoring APO: parameter, which is hidden in the layout.

[15:17:57] ABILIS_CPX:d nat pr:1

-------------------------------------------------------------------------------
PR: [DESCR:]
    INAT:         ADD: SNET:              DNET:              ANET:
    ONAT:              SPO:               DPO:               APO:          PAT:
    SRES:   DRES:      PROT:              TOUT:
-------------------------------------------------------------------------------
1   IN            DST  192.168.032.000/24 Ip-32              Ip-45
    OUT                *                  ''translate-po''                 YES
-------------------------------------------------------------------------------

[15:18:15] ABILIS_CPX:

Improved TRFA IP Traps through the configurability of the instants from which the traffic count is started.

[18:33:03] ABILIS_CPX:d trfa ip trap ? start-day start-time

. . . 

TRFA IP Trap entry parameters:

START-DAY: Monitor starting day.                       <Only for INT:Week|Month>
           For INT:Week  : [MO, TU, WE, TH, FR, SA, SU]
           For INT:Month : [1..31]
START-TIME: Monitor starting time [hh:mm].         <Only for INT:Day|Week|Month>

[18:33:16] ABILIS_CPX:d trfa ip trap

---+----+----------------------------------------------------------------------
         [Res DESCR]
ID: ACT: RES:   VAR:     INT:     START-DAY: START-TIME:         VAL:
---+----+----------------------------------------------------------------------
0   YES  [DO-NOT-CHANGE-NEVER!]
         Ip-2   CHR-TOT  Day                 00:00               100 (Mbytes)
---+----+----------------------------------------------------------------------

[18:36:30] ABILIS_CPX:

In the previous versions, the traffic count for 'Day' interval always started from midnight, the traffic count for 'Week' interval always started from midnight on Monday and the traffic count for 'Month' interval always started from midnight on the 1st day of the month.

With these fixed rules, prepaid or pay-as-you-go SIM cards couldn't be managed properly.

The problem has been solved introducing traffic count starting day/time selection for Day/Week/Month monitoring intervals.

Increased DHCP server buffers from 15 to 50 and halved response wait time.

Dhcp Lan with MODE:SERVER, replaced ICMPCHK parameter with ARPCHK parameter.

[16:47:06] ABILIS_CPXT:d dhcp lan:2

Parameter:   | Value:
-------------+-----------------------------------------------------------------
LAN:           2
NAME:          new
NET:           000.000.000.000/00
MASK:          000.000.000.000
MAC-FILTER:    #
MODE:          SERVER
POOL1:         #
POOL2:         #
POOL3:         #
POOL4:         #
POOL5:         #
PROF:          5
DEF-LEASE:     36000
MAX-LEASE:     36000
ARPCHK:        NO
-------------------------------------------------------------------------------

[16:48:33] ABILIS_CPX:d dhcp lan:2 ? arpchk

D DHCP LAN:xxx[,yyy,...]         Display DHCP subnet [1..128, A]

DHCP Subnet parameters:

ARPCHK:    Enable/disable ARP check before assigning an IP address [NO, YES]

[16:48:42] ABILIS_CPX:

With 'ICMPCHK' it was possible to detect the presence of IPs already assigned using PINGs.

With 'ARPCHK' the verification is done using ARP requests.

Added support for RIOOne board.

The board has 16 digital inputs, 16 digital outputs, 8 analog inputs and 4 digital outputs.

Some commands have been added that allow the elimination of obsolete versions or forgotten files or directories that are no longer used because they derive from no longer existing users.

These command are grouped under 'SYS PURGE' main keywords

[08:29:22] ABILIS_CPX:SYS PURGE ?

ALL            Performs all purges in sequence
USERS          Purge directories and files of not existing users
VERSIONS       Purge versions other than the current one

[08:29:32] ABILIS_CPX:

• SYS PURGE VERSIONS

  This command deletes all versions/builds leaving only the current

  [14:28:13] ABILIS_CPX:sys purge versions
  
  YOU ARE GOING TO KEEP ONLY CURRENT VERSION AND PURGE ALL THE OTHERS.
  PROCEED (N/Y)?y
  
  PURGE VERSIONS IN PROGRESS...
  DELETED '4727' BUILD
  DELETED '4715-8' BUILD
  DELETED '4703-18' BUILD
  DELETED '4726-98' BUILD
  DELETED '4715-10' BUILD
  DELETED '4715-11' BUILD
  DELETED '4703-23' BUILD
  
  COMMAND EXECUTED
  
  [14:29:39] ABILIS_CPX:sys display versions
  
  List of available versions/builds:
  
  Version/Build directory                                  Date         Time
  -------------------------------------------------------------------------------
  4715-12                                                  29/03/2021   13:08:40
  
  [14:31:10] ABILIS_CPX:

• SYS PURGE USERS

  This command deletes all working directories, Voice Mail directories and CTI Traffic analyzer files of no longer existing users.

  [08:42:17] ABILIS_CPX:sys purge users
  
  YOU ARE GOING TO PURGE ALL DIRECTORIES AND FILES OF NOT EXISTING USERs, IF ANY.
  THIS OPERATION MAY TAKE SOME TIME.
  PROCEED (N/Y)?y
  
  PURGE USERS IN PROGRESS...
  DELETED 'C:\APP\USERS\Utente1' DIRECTORY
  DELETED 'C:\APP\USERS\Utente2' DIRECTORY
  DELETED 'C:\APP\VM\USERS\Utente1' DIRECTORY
  DELETED 'C:\APP\VM\USERS\Utente2' DIRECTORY
  DELETED 'C:\APP\TRFA\CTI\USER\Utente1_DAY.DAT' FILE
  DELETED 'C:\APP\TRFA\CTI\USER\Utente2_DAY.DAT' FILE
  DELETED 'C:\APP\TRFA\CTI\USER\Utente1_WEEK.DAT' FILE
  DELETED 'C:\APP\TRFA\CTI\USER\Utente2_WEEK.DAT' FILE
  DELETED 'C:\APP\TRFA\CTI\USER\Utente1_MONTH.DAT' FILE
  DELETED 'C:\APP\TRFA\CTI\USER\Utente2_MONTH.DAT' FILE 
  
  PURGE USERS STATISTICS:
  - Users directories: 2
  - VM Users directories: 2
  - TRFA Cti user files: 6
  - TRFA Cti History user files: 0
  
  COMMAND EXECUTED
  
  [08:44:02] ABILIS_CPX:

• SYS PURGE ALL

  This command performs all purges in sequence, by first on versions and then on users.

Some commands have been added that allow to list and to delete CTI/IP Traffic analyzer files.

• Listing CTI Traffic analyzer files of any user or of users with CTI-TRFA:NO:

  [09:06:08] ABILIS_CPX:d trfa cti files ?
  
  DISABLED       List TRFA files of all users with CTI-TRFA:NO
  USER:          List TRFA files of specified user
  
  [09:06:34] ABILIS_CPX:d trfa cti files disabled
  
  C:\APP\TRFA\CTI\USER\0001_DAY.DAT
  C:\APP\TRFA\CTI\USER\alfred_DAY.DAT
  C:\APP\TRFA\CTI\USER\pcphone_DAY.DAT
  C:\APP\TRFA\CTI\USER\0001_WEEK.DAT
  C:\APP\TRFA\CTI\USER\0001_MONTH.DAT
  C:\APP\TRFA\CTI\USER\alfred_WEEK.DAT
  C:\APP\TRFA\CTI\USER\alfred_MONTH.DAT
  C:\APP\TRFA\CTI\USER\pcphone_WEEK.DAT
  C:\APP\TRFA\CTI\USER\pcphone_MONTH.DAT
  C:\APP\TRFA\CTI\USER\0001_YEAR.DAT
  C:\APP\TRFA\CTI\USER\alfred_YEAR.DAT
  C:\APP\TRFA\CTI\USER\pcphone_YEAR.DAT
  C:\APP\TRFA\CTI\HISTORY\USER\0001_2019.DAT
  C:\APP\TRFA\CTI\HISTORY\USER\alfred_2019.DAT
  C:\APP\TRFA\CTI\HISTORY\USER\pcphone_2019.DAT
  
  [09:06:41] ABILIS_CPX:

• Deleting CTI Traffic analyzer files of any users or of users with CTI-TRFA:NO:

  [09:06:41] ABILIS_CPX:c trfa cti files ?
  
  DISABLED       Remove TRFA files of all users with CTI-TRFA:NO
  USER:          Remove TRFA files of specified user
  
  [09:15:15] ABILIS_CPX:c trfa cti files user:alfred
  
  YOU ARE GOING TO REMOVE TRFA CTI FILES OF USER:alfred, IF ANY.
  THIS OPERATION MAY TAKE SOME TIME.
  PROCEED (N/Y)?y
  
  COMMAND IN PROGRESS...
  DELETED 'C:\APP\TRFA\CTI\USER\alfred_DAY.DAT'
  DELETED 'C:\APP\TRFA\CTI\USER\alfred_WEEK.DAT'
  DELETED 'C:\APP\TRFA\CTI\USER\alfred_MONTH.DAT'
  DELETED 'C:\APP\TRFA\CTI\USER\alfred_YEAR.DAT'
  DELETED 'C:\APP\TRFA\CTI\HISTORY\USER\alfred_2019.DAT'
  
  DELETED 5 FILE
  
  COMMAND EXECUTED
  
  [09:15:28] ABILIS_CPX:

• Listing IP Traffic analyzer files of any resource or of resources with TRFA:NO:

  [09:15:28] ABILIS_CPX:d trfa ip ?
  
  FILES          Trfa IP files
  TRAP           TRFA IP Trap entry
  
  [09:24:40] ABILIS_CPX:d trfa ip files ?
  
  DISABLED       List TRFA files of all IpRes with TRFA:NO
  IPRES:         List TRFA files of specified IpRes
  
  [09:24:46] ABILIS_CPX:d trfa ip files disabled
  
  C:\APP\TRFA\IP\002D.DAT
  C:\APP\TRFA\IP\002W.DAT
  C:\APP\TRFA\IP\002M.DAT
  C:\APP\TRFA\IP\002Y.DAT
  C:\APP\TRFA\IP\502D.DAT
  C:\APP\TRFA\IP\502W.DAT
  C:\APP\TRFA\IP\502M.DAT
  C:\APP\TRFA\IP\502Y.DAT
  C:\APP\TRFA\IP\505D.DAT
  C:\APP\TRFA\IP\505W.DAT
  C:\APP\TRFA\IP\505M.DAT
  C:\APP\TRFA\IP\505Y.DAT
  C:\APP\TRFA\IP\601D.DAT
  C:\APP\TRFA\IP\601W.DAT
  . . .
  C:\APP\TRFA\IP\901Y.DAT
  
  [09:25:03] ABILIS_CPX:

• Deleting IP Traffic analyzer files of any resource or of resources with TRFA:NO:

  [09:25:03] ABILIS_CPX:c trfa ip files ?
  
  DISABLED       Remove TRFA files of all IpRes with TRFA:NO
  IPRES:         Remove TRFA files of specified IpRes
  
  [09:28:59] ABILIS_CPX:c trfa ip files ipres:ip-505
  
  YOU ARE GOING TO REMOVE TRFA IP FILES OF IPRES:505, IF ANY.
  THIS OPERATION MAY TAKE SOME TIME.
  PROCEED (N/Y)?y
  
  COMMAND IN PROGRESS...
  DELETED 'C:\APP\TRFA\IP\505D.DAT'
  DELETED 'C:\APP\TRFA\IP\505W.DAT'
  DELETED 'C:\APP\TRFA\IP\505M.DAT'
  DELETED 'C:\APP\TRFA\IP\505Y.DAT'
  
  DELETED 4 FILE
  
  COMMAND EXECUTED
  
  [09:29:25] ABILIS_CPX:

All bugfixes up to 8.10.4 are included in 8.11.0

None